Many breakdowns of the dishwasher can be eliminated with simple actions. The problems are often associated with low voltage or reduced pressure in the water supply. Many breakdowns are caused by the fact that filters, grids, and holes are clogged in with food deposits. All these problems can be fixed without additional help which will bring the device back to normal operation.
ESpares Washing Machine & Dishwasher Cleaner & Descaler 4.8. Save 14% if you buy 2 or more - Only £4.49 each. This cleaner & descaler product removes limescale & detergent build up in washing machines & dishwashers, leaving them smelling fresh.: just in case we also have ES1641507 - Liquid Appliance Descaler, Kettles, Steam Irons Coffee Makers, Shower Heads Etc More information. This great CDA dishwasher has an impressive A+ energy rating meaning it will use less energy than most dishwashers. The WC140IN dishwasher has an A rating for cleaning - this is the best rating it can get and the B rating for drying is by no means bad either. One of the most useful features the WC140IN has is the delay start timer that means.
CDA CW494 dishwasher troubleshooting
| Problem | Solution |
|---|---|
| The Dishwasher Does Not Start | - the plug is pushed into the socket correctly; |
| - the power is on in the house; | |
| - the door is closed properly; | |
| - the ON-OFF switch is on 'ON”; | |
| - the water supply is turned on. | |
| The Dishwasher Does Not Load Water | - the water is turned on and the hose is connected properly; |
| - the water supply to the house is on and has sufficient pressure; | |
| - the water supply hose is crimped or bent; | |
| - the filter for the water supply hose is clogged. | |
| The Dishes Are Not Clean | - the water is turned on and the hose is connected properly; |
| - the water supply to the house is on and has sufficient pressure; | |
| - the water supply hose is crimped or bent; | |
| - the filter for the water supply hose is clogged | |
| The Dishwasher Does Not Drain | - the drain hose is crimped or bent. |
| Lime Deposits or a White Film Form on the Dishes | - the lid to the salt container is closed properly; |
| - the rinse aid dosage is correct. |
CDA WC370IN dishwasher troubleshooting
| Problem | Possible cause |
|---|---|
| The programme will not start | Check the plug, fuse and circuit breakers of the mains supply. |
| The water tap is turned off. | |
| The dishwasher door is not fully closed. | |
| The water inlet filter or the machine filters are blocked. | |
| Water remains inside the dishwasher at the end of a programme | The water drain hose is blocked or kinked. The filters are blocked. |
| The dishwasher stops in the middle of a programme | Power failure. |
| Water inlet failure. Programme is on standby. | |
| Wash performance is of a low standard | Poor loading of dishes hinders wash performance. Insufficient detergent added. Inappropriate wash programme selected. Spray arm is blocked. |
| Filters clogged or incorrectly fitted. | |
| Water drain pump is blocked. | |
| White stains on the dishes | Insufficient detergent added. |
| Rinse aid setting is too low. | |
| Insufficient dishwasher salt added. | |
| Water softener setting is too low. | |
| Salt compartment cap may not be completely closed. | |
| The dishes are not completely dry at the end of a programme | A programme without a drying stage was selected. |
| Rinse aid setting is too low. | |
| Dishes unloaded too soon (allow time for drying). | |
| There are rust stains on the dishes | Different sets of cutlery should be kept separate. Too much salt (water softener setting is too high). Salt compartment cap not completely closed. Poor appliance earth (check mains electrical supply). |
| The door is not opening or closing properly | Door tension not correctly adjusted for the decor door. |
Cda Dishwasher Wc140in Manuals
CDA WF610BL, WC140in dishwasher troubleshooting
Cda Dishwasher Wc140in Manual User
Cda Dishwasher Wc140in Manual Troubleshooting
| Error Code | Error description | Advice |
|---|---|---|
| F01 | Water leakage has been detected | • Turn off the dishwasher and disconnect the water supply |
| • Contact CDA Customer Care | ||
| F02 | The waste water cannot be discharged | • Drain hose is blocked |
| • The filters of your machine might be blocked | ||
| • Restart the dishwasher and cancel the programme | ||
| • If the error continues, contact CDA Customer Care | ||
| F03 | Continual fill error | • Contact CDA Customer Care |
| F04 | Faulty flow meter | |
| F05 | Inadequate water supply | • Make sure the water tap is fully open |
| • Close the water tap, separate the water inlet hose from the tap and clean the filter. | ||
| • Restart the dishwasher. | ||
| • If the error continues, contact CDA Customer Care | ||
| F06 | Faulty NTC | • Contact CDA Customer Care |
| F07 | Water temperature too high | |
| F08 | Heater error: Inadequate heat | |
| F09 | Diverter position problem | |
| F00 | Alarm is active against water overflow | |
| FE | Electronic card parameter faulty | |
| SE | Electronic card water hardness faulty | • Check the water hardness is set for your water supply |
| • If the error continues, contact CDA Customer Care | ||
| FA | Faulty turbidity sensor | • Contact CDA Customer Care |